Reference health
A systematic study of vat-polymerization binders with potential use in the ceramic suspension 3D printing
33/33 checkable references clean · checked 2026-07-22
Every reference with a DOI in the deposited reference list resolved to a known work in Crossref or DataCite at the dated check, and none carried a retraction, withdrawal, or removal notice.
14 without a DOI — not checked. A reference deposited without a DOI is never matched by title or guessed at; it stays outside the checked set, and this line discloses that.
The 33 checked references that resolve
resolves10.1146/annurev-matsci-070115-031841
Ceramic Stereolithography: Additive Manufacturing for Ceramics by Photopolymerization
resolves10.1108/13552549810222867
Stereolithography for the fabrication of ceramic three‐ dimensional parts
resolves10.3390/ma10020138
Influence of Resin Composition on the Defect Formation in Alumina Manufactured by Stereolithography
resolves10.1016/j.ceramint.2016.11.143
The effect of the surfactants on the formulation of UV-curable SLA alumina suspension
resolves10.1016/j.ceramint.2013.09.059
Optimization of rheological properties of photopolymerizable alumina suspensions for ceramic microstereolithography
resolves10.1016/j.ceramint.2020.01.152
Preparation and biological evaluation of ZrO2 all-ceramic teeth by DLP technology
resolves10.1016/j.ceramint.2019.03.024
Preparation of high solid loading and low viscosity ceramic slurries for photopolymerization-based 3D printing
resolves10.1111/j.1744-7402.2010.02568.x
Integrally Cored Ceramic Mold Fabricated by Ceramic Stereolithography
resolves10.1016/j.jeurceramsoc.2018.09.013
Mechanical and kinetic studies on the refractory fused silica of integrally cored ceramic mold fabricated by additive manufacturing
resolves10.1016/j.jphotochem.2011.05.010
Photopolymerization kinetics of a polyether acrylate in the presence of ceramic fillers used in stereolithography
resolves10.1080/10601329708014988
Photoinitiated Polymerization of Vinyl Ether and Acrylate Monomer Mixtures
resolves10.1016/j.ceramint.2016.10.027
Fabrication of dense zirconia-toughened alumina ceramics through a stereolithography-based additive manufacturing
resolves10.1016/j.jeurceramsoc.2019.05.023
Development of UV-curable ZrO2 slurries for additive manufacturing (LCM-DLP) technology
resolves10.1002/pola.23734
Vinyl esters: Low cytotoxicity monomers for the fabrication of biocompatible 3D scaffolds by lithography based additive manufacturing
resolves10.1016/j.matdes.2019.107960
Optimization and characterization of high-viscosity ZrO2 ceramic nanocomposite resins for supportless stereolithography
resolves10.3390/ma11122350
Rheological and Curing Behavior of Acrylate-Based Suspensions for the DLP 3D Printing of Complex Zirconia Parts
resolves10.1016/0278-6125(93)90311-G
Rapid prototyping & manufacturing— Fundamentals of stereolithography
resolves10.1515/arh-2001-0006
An examination of the use of rotational viscometers for the quality control of non-Newtonian liquid products in factories
resolves10.1016/S0032-3861(00)00141-5
The effect of temperature on the kinetics of diacrylate photopolymerizations studied by Real-time FTIR spectroscopy
resolves10.1016/S0032-3861(97)00184-5
Photoinitiated polymerization of a dimethacrylate oligomer: 1. Influence of photoinitiator concentration, temperature and light intensity
resolves10.1177/00220345990780081301
The Effects of Light Intensity, Temperature, and Comonomer Composition on the Polymerization Behavior of Dimethacrylate Dental Resins
resolves10.1016/j.ceramint.2014.12.066
Effect of surfactant on dispersion of alumina in photopolymerizable monomers and their UV curing behavior for microstereolithography
resolves10.1002/app.1991.070420503
Chemical reactions in crosslinking of copolymers of ethylene and vinyltrimethoxy silane
The 14 references without a DOI — listed, not checked
no DOI — not checkedAdditive manufacturing of ceramics: a review
no DOI — not checkedMeasuring UV curing parameters of commercial photopolymers used in additive manufacturing
no DOI — not checkedEpoxy based blends for additive manufacturing by liquid crystal display (LCD) printing: the effect of blending and dual curing on daylight curable resins
no DOI — not checkedA comprehensive review of the photopolymerization of ceramic resins used in stereolithography
no DOI — not checkedMechanical characterization of 3D-printed polymers
no DOI — not checkedA review on the rheological behavior and formulations of ceramic suspensions for vat photopolymerization
no DOI — not checkedPhotopolymer formulation to minimize feature size, surface roughness, and stair-stepping in digital light processing-based three-dimensional printing
no DOI — not checkedStandard practice for preparation of metallographic specimens
no DOI — not checkedISO 19403–3, Paints and varnishes — Wettability — Part 3: Determination of the surface tension of liquids using the pendant drop method.”
no DOI — not checked10.1016/j.addma.2021.102225_bib35
no DOI — not checkedHot Lithography vs. room temperature DLP 3D-printing of a dimethacrylate
no DOI — not checkedCombining cure depth and cure degree, a new way to fully characterize novel photopolymers
no DOI — not checkedDetermination of Reaction Rate Coefficients in Free-Radical Polymerization Using Density Functional Theory
no DOI — not checkedComprehensive Polymer Science
What this badge says. CiteStamped means the CHECKABLE references of this
work were clean at the dated check: each resolved to a known work in a public registry, and none
carried a retraction notice at that time. It says nothing about the quality, findings,
or importance of the work itself, and nothing about references deposited without a DOI.
checked 2026-07-22 — re-checked daily as this page is visited; titles and statuses come from Crossref and DataCite and are not part of the signed record
Embed this badge
Both snippets point at the live badge image and link back to this page. The badge re-renders from the daily check, so an embed never goes stale by more than a day of visits.
<a href="https://citestamp.com/citestamped/10.1016/j.addma.2021.102225"><img src="https://citestamp.com/citestamped/10.1016/j.addma.2021.102225/badge.svg" alt="CiteStamped reference-health badge" width="460" height="64"></a>
[](https://citestamp.com/citestamped/10.1016/j.addma.2021.102225)