Reference health

Rate effects on localized shear deformation during nanosectioning of an amorphous thermoplastic polymer

https://doi.org/10.1016/j.ijsolstr.2017.09.016
CiteStamped reference-health badge
29/29 checkable references clean · checked 2026-07-22

Every reference with a DOI in the deposited reference list resolved to a known work in Crossref or DataCite at the dated check, and none carried a retraction, withdrawal, or removal notice.

10 without a DOI — not checked. A reference deposited without a DOI is never matched by title or guessed at; it stays outside the checked set, and this line discloses that.

The 29 checked references that resolve
resolves10.1007/BF02642598
On microscopic plastic instabilities in metal machining chips
resolves10.1016/0141-6359(93)90105-J
Ultraprecision machining of polymers
resolves10.1016/j.ijmachtools.2005.05.015
Investigation of micro-cutting operations
resolves10.1016/j.jmatprotec.2013.05.017
Ductile shear failure damage modelling and predicting built-up edge in steel machining
resolves10.1016/S0007-8506(07)63020-0
On Chip Morphology, Tool Wear and Cutting Mechanics in Finish Hard Turning
resolves10.1098/rsta.2000.0756
Thermomechanical oscillations in material flow during high-speed machining
resolves10.1016/j.matdes.2008.04.029
A study of plastic strain and plastic strain rate in machining of steel AISI 1045 using FEM analysis
resolves10.1016/S0032-3861(96)01051-8
Design and potential of instrumented ultramicrotomy
resolves10.5254/1.3536170
The Influence of Frictional Heating on the Sliding Friction of Elastomers and Polymers
resolves10.1016/j.ijmachtools.2005.03.010
Modelling and experimental investigation on nanometric cutting of monocrystalline silicon
resolves10.1016/S0020-7403(97)00017-9
Modeling of thermomechanical shear instability in machining
resolves10.1016/S0890-6955(98)00084-4
Effects of process parameters on material side flow during hard turning
resolves10.1002/pol.1962.1205816691
On the cutting mechanism of high polymers
resolves10.1007/s11661-002-0284-1
On thermoplastic shear instability in the machining of a titanium alloy (Ti-6Al-4V)
resolves10.1016/j.ijsolstr.2012.08.013
Contact variables and thermal effects at the tool–chip interface in orthogonal cutting
resolves10.1016/j.ijmachtools.2005.07.001
The influence of friction models on finite element simulations of machining
resolves10.1016/j.engfracmech.2009.07.019
Determining fracture toughness from cutting tests on polymers
resolves10.1016/j.polymer.2005.05.079
A formulation of the cooperative model for the yield stress of amorphous polymers for a wide range of strain rates and temperatures
resolves10.1016/j.ijsolstr.2005.06.040
Influence of temperature and strain rate on the mechanical behavior of three amorphous polymers: Characterization and modeling of the compressive yield stress
resolves10.1016/j.jmps.2007.09.003
Dynamic flow and failure of confined polymethylmethacrylate
resolves10.1115/1.3123337
Effect of Carbon Nanotube (CNT) Loading on the Thermomechanical Properties and the Machinability of CNT-Reinforced Polymer Composites
resolves10.1016/j.engfracmech.2017.05.044
Polymer fracture and deformation during nanosectioning in an ultramicrotome
resolves10.1016/j.ijmachtools.2009.02.008
Characteristics of cutting forces and chip formation in machining of titanium alloys
resolves10.1016/0025-5416(82)90082-9
Calculation of shear strains in chip formation in titanium
resolves10.1007/s11661-007-9271-x
Shear Localization: A Historical Overview
resolves10.1016/j.ijmachtools.2011.02.010
Dynamic modelling of shear band formation and tool-tip vibration in ultra-precision diamond turning
resolves10.1088/0508-3443/18/8/317
The influence of pre-orientation on the optical and mechanical anisotropy of drawn polymers
resolves10.1080/14786437508229629
Adiabatic shear of titanium and polymethylmethacrylate
resolves10.1016/j.engfracmech.2009.07.023
Mixed mode fracture toughness as a separation parameter when cutting polymers
The 10 references without a DOI — listed, not checked
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0001
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0002
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0006
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0008
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0012
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0016
no DOI — not checkedMechanics of Machining: An Analytical Approach to Assessing
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0028
no DOI — not checkedSun, F., Mechanical Properties and Deformation Behaviour of Polymer Materials during Nanosectioning: Characterisation and Modelling, PhD thesis, 2017b, Uppsala University.
no DOI — not checked10.1016/j.ijsolstr.2017.09.016_bib0032
What this badge says. CiteStamped means the CHECKABLE references of this work were clean at the dated check: each resolved to a known work in a public registry, and none carried a retraction notice at that time. It says nothing about the quality, findings, or importance of the work itself, and nothing about references deposited without a DOI.

checked 2026-07-22 — re-checked daily as this page is visited; titles and statuses come from Crossref and DataCite and are not part of the signed record

view as graph · paper page

Embed this badge

Both snippets point at the live badge image and link back to this page. The badge re-renders from the daily check, so an embed never goes stale by more than a day of visits.

<a href="https://citestamp.com/citestamped/10.1016/j.ijsolstr.2017.09.016"><img src="https://citestamp.com/citestamped/10.1016/j.ijsolstr.2017.09.016/badge.svg" alt="CiteStamped reference-health badge" width="460" height="64"></a>
[![CiteStamped reference-health badge](https://citestamp.com/citestamped/10.1016/j.ijsolstr.2017.09.016/badge.svg)](https://citestamp.com/citestamped/10.1016/j.ijsolstr.2017.09.016)