Reference health

Options for additive rapid prototyping methods (3D printing) in MEMS technology

https://doi.org/10.1108/rpj-04-2013-0038
CiteStamped reference-health badge
19/19 checkable references clean · checked 2026-07-23

Every reference with a DOI in the deposited reference list resolved to a known work in Crossref or DataCite at the dated check, and none carried a retraction, withdrawal, or removal notice.

6 without a DOI — not checked. A reference deposited without a DOI is never matched by title or guessed at; it stays outside the checked set, and this line discloses that.

The 19 checked references that resolve
resolves10.1108/13552540610670717
Advances in three dimensional printing – state of the art and future perspectives
resolves10.1007/978-1-4419-1120-9_14
Direct Digital Manufacturing
resolves10.1088/0960-1317/20/10/104009
Direct write dispenser printing of a zinc microbattery with an ionic liquid gel electrolyte
resolves10.1007/s00170-012-4558-5
Additive manufacturing and its societal impact: a literature review
resolves10.1063/1.2965615
Superhydrophobic membranes with electrically controllable permeability and their application to “smart” microbatteries
resolves10.1109/JMEMS.2010.2090504
Robust Si-Based Membranes for Fluid Control in Microbatteries Using Superlyophobic Nanostructures
resolves10.1109/JMEMS.2012.2208218
Design and Fabrication of Addressable Microfluidic Energy Storage MEMS Device
resolves10.1108/13552540710736759
Process planning method for mask projection micro‐stereolithography
resolves10.1016/j.jmatprotec.2012.12.015
Surface modification of fused deposition modeling ABS to enable rapid prototyping of biomedical microdevices
resolves10.1108/13552540410512543
Freeform fabrication of zinc‐air batteries and electromechanical assemblies
resolves10.1016/S1369-7021(10)70223-6
Medical prototyping using two photon polymerization
resolves10.1039/C0LC00331J
Fabrication of monolithic 3D micro-systems
resolves10.1007/978-0-387-46283-7_7
Stereolithography and Rapid Prototyping
resolves10.1039/c1lc20514e
Rapid prototyping polymers for microfluidic devices and high pressure injections
resolves10.1016/j.sna.2004.12.011
Projection micro-stereolithography using digital micro-mirror dynamic mask
resolves10.1109/JPROC.2003.813570
Microfluidics meets MEMS
resolves10.1117/12.454606
<title>Application of fused deposition modeling rapid prototyping system to the development of microchannels</title>
resolves10.1109/JMEMS.2003.820936
Etch rates for micromachining processing-part II
resolves10.1109/84.546406
Etch rates for micromachining processing
The 6 references without a DOI — listed, not checked
no DOI — not checkedBertsch, A. , Jiguet, S. , Bernhard, P. , Renaud, P. , Pique, A. , Holmes, A.S. and Dimos, D.B. (2003), “Microstereolithography: a review”, in Symposim on Rapid Prototyping Technologies, Vol. 758, MRS, Boston, pp. 3-15.
no DOI — not checkedChua, C.K. , Kah Fai, L. and Lim, C.S. (2010), Rapid Prototyping: Principles and Applications, World Scientific, Singapore; Hackensack, NJ.
no DOI — not checkedMadou, M. (2009), Fundamentals of Microfabrication and Nanotechnology, Taylor & Francis, CRC, Boca Raton, London.
no DOI — not checkedMoore, J.L. , McCuiston, A. , Mittendorf, I. , Ottway, R. and Johnson, R.D. (2010), “Behavior of capillary valves in centrifugal microfluidic devices prepared by three-dimensional printing”, Microfluidics and Nanofluidics, Vol. 10 No. 7, pp. 877-888.
no DOI — not checkedPique, A. (2001), Direct Write Technologies for Rapid Prototyping: Applications to Sensors, Electronics and Passivation Coatings, Academic, San Diego, CA, London.
no DOI — not checkedVaezi, M. , Seitz, H. and Yang, S. (2012), “A review on 3d micro-additive manufacturing technologies”, The International Journal of Advanced Manufacturing Technology, Vol. 67 Nos 5/8, pp. 1721-1754, www.springerlink.com/index/10.1007/s00170-012-4605-2
What this badge says. CiteStamped means the CHECKABLE references of this work were clean at the dated check: each resolved to a known work in a public registry, and none carried a retraction notice at that time. It says nothing about the quality, findings, or importance of the work itself, and nothing about references deposited without a DOI.

checked 2026-07-23 — re-checked daily as this page is visited; titles and statuses come from Crossref and DataCite and are not part of the signed record

view as graph · paper page

Embed this badge

Both snippets point at the live badge image and link back to this page. The badge re-renders from the daily check, so an embed never goes stale by more than a day of visits.

<a href="https://citestamp.com/citestamped/10.1108/rpj-04-2013-0038"><img src="https://citestamp.com/citestamped/10.1108/rpj-04-2013-0038/badge.svg" alt="CiteStamped reference-health badge" width="460" height="64"></a>
[![CiteStamped reference-health badge](https://citestamp.com/citestamped/10.1108/rpj-04-2013-0038/badge.svg)](https://citestamp.com/citestamped/10.1108/rpj-04-2013-0038)